Rolling Knife Sharpener Set, 5 Angles, Diamond & Polishing Discs
Rolling Knife Sharpener Set, 5 Angles, Diamond & Polishing Discs
Set it once, then drill every door and drawer in your kitchen without measuring each one.
Set once, repeat on every door and drawer. No tape measure, no pencil marks.
Flip it for the opposite door. No resetting.
Center notch lines up the jig with the middle of a drawer front.
Drill bit and stop collar included. Start drilling right away.
Couldn't load pickup availability
Often cheaper than replacing one ruined door. Backed by our 30-day money-back guarantee.
Complete the set and save 10%
Cabinet Hardware Jig – Drill Every Pull and Knob in the Same Spot
Drill every pull and knob in the same spot
35 mm Concealed Hinge Drilling Jig, Quick Clamp, Aluminum Alloy
Drill hinge cups at the right depth and position
2-in-1 Cabinet Door Installation Jig with Drill Guide Set, Aluminum Alloy
Support and align the door before the first screw
-
Ordered
- - -
Shipped
- - -
Delivered
-
Paid for itself on my very first cabinet installation! Installed handles on 20+ doors in under two hours with zero misdrilled holes. Absolutely solid tool.
-
I'm just a DIYer updating our kitchen, and this made installing cabinet pulls a walk in the park. Measure twice, lock the screws, and drill with 100% confidence.
-
Game changer for my business. Saves my crew hours on every kitchen job. The laser-etched markings are super precise and easy to read.
Free shipping
- 30-Day Return Policy
Secure Payment
Specifications
Specifications
- Body: aluminum alloy T-plate and scaled bar
- Guide bushings: stainless steel
- Scales: millimeters and inches
- Main bar scale: ±150 mm (±6 in) from the center
- Hole spacing: up to 12 in (300 mm), center to center
- Guides: adjustable sliding guide blocks
- Center notch: aligns the jig to the middle of a drawer front
- Drill bit: 5 mm, with a stop collar to set drilling depth
- Made for: pulls and knobs on flat doors and drawer fronts
What's in the box
What's in the box
Standard Kit
- Cabinet hardware jig (aluminum T-plate with scaled bar and sliding guide blocks)
- 5 mm drill bit
- Stop collar
- Hex key
Pro Kit
- Everything in the Standard Kit
- 400 mm extension bar
Drill, screws, pulls and knobs are not included.
Shipping Information
Shipping Information
We currently ship to the United States, Canada, the United Kingdom, and Australia.
Orders are processed within 1–3 business days. Once shipped, delivery typically takes 7–12 business days, so most orders arrive within 8–15 business days of being placed. Delivery times are estimates and may be longer during peak seasons or due to customs processing.
If your order contains multiple items, they may ship separately from different warehouses and arrive at different times. Tracking information will be provided for each shipment, where available.
Money back guarantee
Money back guarantee
Not Completely Satisfied? We’re Here to Help.
Have a question about your order, an issue with your product, or need to make a return? Contact us and we’ll sort it out.
30-day money-back guarantee. If your order doesn’t meet your expectations, contact us at hictoolsmith@gmail.com within 30 days of delivery and we’ll help you with the next steps. We reply within 1–2 business days.
- Damaged, defective or wrong item? Send us your order number and a photo, and we’ll send a replacement or refund your purchase.
- Changed your mind? Return the item in good working condition with all included parts, and we’ll refund your purchase once we receive it. Return shipping is paid by the customer.
Your satisfaction matters to us. See our full Refund Policy.
Rolling Knife Sharpener Set, 5 Angles, Diamond & Polishing Discs
One crooked hole can ruin a whole door
Mark each door by hand and every pull lands in a slightly different spot. A wrong hole in a finished door can't be undone. Set the jig once and every door and drawer gets the same hole position.
Set once. Drill the rest.
1. Set the spacing. Slide the guide blocks to match your pull's hole spacing.
2. Position. Rest the T-plate on the door or drawer edge and set the distance.
3. Drill. Drill straight through the guide holes.
4. Flip for the next door. Same settings, mirror-image result.
Precision Made Simple
Skip repetitive measuring and marking. Our anodized aluminum jig with laser-engraved scales and stainless steel guide bushings makes every installation faster, easier, and more precise.
One Jig. The Same Hole Position. Every Time.
Designed for cabinet doors, drawer fronts, dressers, and built-ins. Set your handle spacing once and repeat it across every surface for a clean, consistent finish. The center notch helps align the jig, while its reversible design works for both left- and right-hand cabinet doors.
From small knobs to long bar pulls
Spacing goes up to 12 in (300 mm), so one jig covers knobs, standard pulls and long bar pulls.
Common sizes: 3 in (76 mm), 3-3/4 in (96 mm), 5-1/16 in (128 mm), 7-9/16 in (192 mm), 10 in (256 mm).
Jig vs. tape measure and pencil
Why a jig beats measuring every door by hand.
| HiC Toolsmith | Tape measure & pencil | |
|---|---|---|
| Same spot on every door | ||
| Center notch for drawer fronts | ||
| Flip it for left and right doors | ||
| No pencil marks or re-measuring | ||
| Lower risk of off-center holes |
Before you drill: three quick tips
1. Back the exit side. Clamp a scrap block behind the door or drawer front so the bit does not splinter the wood where it comes out.
2. Check the first hole. Drill one hole, test it with your pull, then repeat the same setup on the rest.
3. Tighten before each door. Make sure the guide blocks are snug, then drill.
What customers say
-
1w ago
I was terrified of ruining my new $6,000 custom kitchen cabinets. Bought this jig after watching a TikTok video. Set the measurements once, clamped it down, and every single handle lined up dead center on the first try. Best $80 I’ve ever spent on a DIY project!
353
11 Comments
LikeCommentShare -
2d ago
Game changer for our cabinet installations! We used to waste hours measuring and double-checking each door with a tape measure. With this jig, we installed 28 handles in under 30 minutes. Zero errors, zero damaged doors. Highly recommend it!
85
5 Comments
LikeCommentShare -
3w ago
Upgraded to the Pro Kit with the extension bar and it made installing long pulls on our wide island drawers so easy. Absolutely dead level with zero wobble. My wife thinks I hired a professional!
567
26 Comments
LikeCommentShare
Frequently Asked Questions
Does it work on drawers?
Does it work on drawers?
Yes. A center notch aligns the jig to the drawer front.
Can I use it on left and right doors?
Can I use it on left and right doors?
Yes. Set it once and flip it over for the opposite door, so you don't need to re-measure.
How do I set it up?
How do I set it up?
Slide the guide blocks to your pull's hole spacing and tighten them. Rest the T-plate on the door or drawer edge and set the distance. Clamp a scrap block behind the door, then drill straight through the guide holes. For the next door, keep the same settings, or flip the jig for the opposite side.
The full steps are above: "Set once. Drill the rest." and "Before you drill".
What hole spacing can it set?
What hole spacing can it set?
The main bar sets spacing up to 12 in (300 mm), center to center. That covers single-hole knobs, standard pulls and long bar pulls. Common sizes include 3 in (76 mm), 3-3/4 in (96 mm), 5-1/16 in (128 mm), 6-5/16 in (160 mm), 7-9/16 in (192 mm), 8-13/16 in (224 mm) and 10 in (256 mm).
Does it have inch and metric scales?
Does it have inch and metric scales?
Yes. The bars carry both millimeter and inch markings.
What is it made of?
What is it made of?
An aluminum alloy body with stainless steel guide bushings.
What drill bit is included?
What drill bit is included?
A 5 mm bit with a stop collar to set the depth. It is included in both the Standard and Pro kits.
What is in the box?
What is in the box?
Standard Kit: the jig, a 5 mm drill bit, a stop collar and a hex key.
Pro Kit: everything in the Standard Kit plus a 400 mm extension bar.
A drill, screws, pulls and knobs are not included.
How long does delivery take?
How long does delivery take?
Orders are processed in 1-3 business days, then take 7-12 business days to arrive (8-15 business days in total). If your order has more than one item, the items may ship separately from different locations and arrive on different days.
How do I avoid splintering on the back of the door?
How do I avoid splintering on the back of the door?
Clamp a scrap block of wood behind the door or drawer front before you drill, or put a layer of painter's tape on the exit side. The bit then comes out into the scrap instead of tearing the finished surface.
How many doors can I do with one setup?
How many doors can I do with one setup?
As many as share the same hole spacing and position. Set the jig for one size, drill every door and drawer that uses it, then reset for the next size.